5D-LED-Car-Tail-Logo-Light-Badge-Lamp-Emblem-For-Chevrolet-Holden-Cruze-Malibu-EPICA-CAPTIVA zoom

Hover

5D-LED-Car-Tail-Logo-Light-Badge-Lamp-Emblem-For-Chevrolet-Holden-Cruze-Malibu-EPICA-CAPTIVA-1 zoom

Hover

5D-LED-Car-Tail-Logo-Light-Badge-Lamp-Emblem-For-Chevrolet-Holden-Cruze-Malibu-EPICA-CAPTIVA-2 zoom

Hover

5D-LED-Car-Tail-Logo-Light-Badge-Lamp-Emblem-For-Chevrolet-Holden-Cruze-Malibu-EPICA-CAPTIVA-3 zoom

Hover

5D-LED-Car-Tail-Logo-Light-Badge-Lamp-Emblem-For-Chevrolet-Holden-Cruze-Malibu-EPICA-CAPTIVA
5D-LED-Car-Tail-Logo-Light-Badge-Lamp-Emblem-For-Chevrolet-Holden-Cruze-Malibu-EPICA-CAPTIVA-1
5D-LED-Car-Tail-Logo-Light-Badge-Lamp-Emblem-For-Chevrolet-Holden-Cruze-Malibu-EPICA-CAPTIVA-2
5D-LED-Car-Tail-Logo-Light-Badge-Lamp-Emblem-For-Chevrolet-Holden-Cruze-Malibu-EPICA-CAPTIVA-3
Full Screen

5D LED Car Tail Logo Light Badge Lamp Emblem For Chevrolet Holden Cruze Malibu EPICA CAPTIVA AVEO LOVR

$35.06

Compare
Sold By Sell Out Shop
Vendor Profile:View My Profile SKU: 1005002454111167 Category: Tag:

Recommended For You

$35.06

$35.06

$35.06

Sell Out Shop

Sold By Sell Out Shop
Vendor Profile:View My Profile SKU: 1005002454111167 Category: Tag:

Description

  • Brand Name: CNW-SHS
  • Certification: NONE
  • Origin: CN(Origin)
  • Item Type: Atmosphere Lamp
 

Note: Pro, this product is suitable For for all Chevrolet of cars
Voltage:12 (V)
Size: 17.0*5.5cm
Wiring length: 0.6 meters
Weight: 80G
Material: ABS plating, 3M glue at the bottom
Package Contents:1*Car Auto Tail Logo Light(Other accessories are not included)
Note:
Avoid giving children a play. Do not accidentally install or disassemble this product during driving.
[Tools prepared before installation]
Please have the following tools ready before you start: 1. Flat head screwdriver 2. Phillips screwdriver 3. Insulating tape 4. Towel 5. Pliers
【Installation Notes】
1. First place a towel next to the tailgate logo, use a flat-blade screwdriver to shake the logo, and towel to prevent scratching the body.
2. Pay attention to peeling off the double-sided rubber first. When the squatting is moderate, don’t be too fierce. After a little bit, slowly squat down, clean the car logo and the double-sided tape on the body.
3. Use a Phillips screwdriver to remove the partition inside the tail box. Note that there are clips in some places. Be careful to remove the baffles to see the various lines.
4. Now install the car standard light, the car standard light power line passes through one of the car standard positioning holes,
and wears the single-sided glue on the back of the car standard light inside the car box.
While pulling the wire, the car mark light is glued to the vehicle body, and the pressure is pressed. tight.
5. The car light is installed, and now it is connected to the power supply.
The car light should be connected to the power supply of the license plate, so that when the night light is turned on, the car light will be turned on at the same time, and the power connector of the rear license plate light is found.
Notes:
Due to the light and screen setting difference, the item’s color may be slightly different from the pictures.

Additional information

color

, ,

Reviews

There are no reviews yet.

Be the first to review “5D LED Car Tail Logo Light Badge Lamp Emblem For Chevrolet Holden Cruze Malibu EPICA CAPTIVA AVEO LOVR”
Review our product to get a chance to receive coupon!